We have uncovered this great article on Installing A Bathtub below on the net and figured it made perfect sense to share it with you here.
Mounting a tub isn't precisely rocket science, but it does require solid plumbing, woodworking, and also often, tiling abilities. Changing an old bathtub with a brand-new one is additionally a reasonably hard project. If the old tub is conveniently easily accessible, the task can move quickly; if you need to open a wall to eliminate the old bathtub and also position the brand-new tub, the job is much harder. In either case, the task is within a home handyman's abilities, although you will certainly require an assistant to leave the old bathtub and also set in the brand-new one. See to it you have actually certified on your own for the job as well as fit attempting it. As opposed to working with a professional to take over a halfway-completed project, it is better to think about using one before you start. Opportunities are you may require a specialist plumber to make tube links.
This write-up will certainly help you mount a brand-new bath tub in your washroom if you have actually already gotten a new tub as well as do not need to change the setup of your previous water system pipes.
Your devices and also material checklist need to make up the following:
Removing Old Touches
If you need to change old taps with brand-new ones as a part of your installment, then the first thing you should do is detach the water system. After doing so, switch on the faucets to drain pipes any water remaining in the system. The procedure of getting rid of the existing faucets can be quite problematic due to the restricted accessibility that is typically the situation.
Utilize a basin wrench (crowsfoot spanner) or a faucet tool to reverse the nut that connects the supply pipes to the faucets. Have a towel all set for the continuing to be water that will certainly originate from the pipelines. As soon as the supply pipelines have been eliminated, make use of the exact same device to loosen up the nut that holds the taps onto the bath/basin. You will certainly require to quit the single taps from turning during this procedure. As soon as the faucets have been gotten rid of, the holes in the bath/basin will certainly need to be cleaned up of any type of old securing substance.
Before going on to fit the brand-new faucets, contrast the pipe connections on the old taps to the brand-new faucets. If the old taps are longer than the new faucets, then a shank adapter is required for the new taps to fit.
Suitable New Touches
If the tails of the brand-new taps are plastic, then you will certainly require a plastic port to prevent damage to the thread. One end of the adapter fits on the plastic tail of the tap and the other end offers a link to the current supply pipelines.
If you require to fit a monobloc, after that you will certainly require reducing couplers, which connects the 10mm pipeline of the monobloc to the common 15mm supply pipeline.
Next, position the faucet in the installing opening in the bath/basin guaranteeing that the washing machines remain in area between the faucet and also the sink. Safeguard the tap in place with the manufacturer given backnut. As soon as the tap is firmly in place, the supply pipes can be linked to the tails of the faucets. The taps can either be linked by utilizing corrugated copper piping or with regular faucet connectors. The previous kind must be attached to the tap finishes first, tightening only by hand. The supply pipes can later on be connected to the other end. Tighten up both ends with a spanner after both ends have been attached.
Mounting the Bath tub
Making use of both wood boards under its feet, position the tub in the called for placement. The wood boards are handy in evenly spreading out the weight of the bath tub over the area of the boards instead of concentrating all the weight onto 4 little factors.
The following goal is to guarantee that the bath tub is leveled all round. This can be accomplished by inspecting the spirit level and also adjusting the feet on the bath tub up until the level checks out level.
To mount faucets, fit all-time low of the outermost adaptable tap connector to the appropriate supply pipe by making a compression sign up with; after that do the same for the various other tap.
Activate the supply of water and examine all joints and brand-new pipework for leakages and also tighten them if necessary. Load the bath tub and likewise check the overflow electrical outlet and also the regular outlet for leaks.
Finally, deal with the bath paneling as defined in the maker's user's manual. Tiling and sealing around the tub must wait up until the bathtub has been utilized a minimum of when as this will settle it into its final placement.
Preparing for the Setup
First of all, the sustaining structure supplied with the bathroom should be fitted (if called for) according to the maker's guidelines. Next off, fit the taps or mixer to the bathtub. When suitable the tap block, it is necessary to ensure that if the tap comes with a plastic washing machine, it is fitted in between the bath and the taps. On a plastic bathroom, it is also reasonable to fit a sustaining plate under the faucets system to avoid pressure on the bathtub.
Fit the flexible faucet adapters to the bottom of both taps utilizing 2 nuts and also olives (occasionally provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and then pass the outlet with the hole in the bathroom. Utilize the nut supplied by the producer to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the flexible overflow pipe to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which should be fitted inside the bath. Ensure you utilize all of the provided washing machines.
Link the trap to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Attach all-time low of the overflow tube in a similar manner.The bathroom must now prepare to be suited its final placement.
Tiling Around the Bathtub
In the area where the bathroom fulfills the floor tile, it is necessary to secure the joins with a silicone rubber caulking. This is very important as the installation can move enough to crack a rigid seal, triggering the water to penetrate the wall surface between the bath and also the tiling, bring about difficulties with wetness as well as possible leakages to the ceiling listed below.
You can select from a selection of coloured sealers to blend in your components and also fittings. They are sold in tubes and cartridges, as well as can securing voids as much as a width of 3mm (1/8 inch). If you have a bigger space to load, you can load it with spins of drenched paper or soft rope. Remember to constantly load the bathtub with water prior to sealing, to enable the movement experienced when the bathtub is in usage. The sealant can break relatively early if you do not consider this activity before securing.
Conversely, ceramic coving or quadrant ceramic tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to dimension, are also quickly offered on the marketplace. It is suggested to fit the ceramic tiles using water-resistant or water resistant sticky and also cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
Hopefully you enjoyed reading our piece on A Step-by-Step Guide to Installing a Bathtub. Thank you so much for taking time to browse our content. Do you know anybody else who is occupied with the niche? Why not promote it. Thanks a lot for your time. Please pay a visit to our website back soon.
Book